How to Fix a Busted Charging Unit Single-Handedly

Why do questions like “how to fix a phone charger” arise? Modern devices like smartphones, laptops, audio systems, and other gadgets are not Perpetuum mobiles but need periodical charging. However, power chargers tend to go haywire often for various reasons. The problem is compounded when using the same cord to top up several devices.

Indeed, you will hardly handle the issue if the charger is busted. Do not worry! Everything is resolved easily enough, and there is no need to waste time buying a new charging set. For this purpose, you are not necessarily to be a pro. Just keep reading to dive into a detailed guide and follow clear instructions to reveal an actual problem and put everything back the way it should be. So, how to fix a charger to keep your phone fed?

Measures to Take on a Preliminary Stage: Check All Options

Many types of damages may prevent you from using your mobile when needed. Some issues are fatal. Some are not cost-effective to repair, while others are easy to fix. Although a broken cord is not a disaster, it requires some knowledge to cope with the problem.

Several alternatives should be considered before shoveling many facts to learn how to fix a broken phone charger. After all, even the wall socket might be cut off power or completely damaged. For this reason, the following information highlights possible problems to let you see your case and take steps in the right direction.

Use Another Power Source to Check Your Cable’s Workability

First, make sure that not a cell phone is responsible for the trouble. Maybe, it requires repair or replacement because it has exhausted all resources? However, we hope for less money-consuming solutions. Thus, the simplest way to clarify the situation is to take or borrow from your neighbors and plug another power cord into your mobile device. When no power enters your smartphone or tablet, most likely the real problem lies in the gadget. Therefore, do not be disappointed in trying to fix a broken phone charger.

In contrast, if that cable starts feeding your phone, and the latter works flawlessly, you need to think about how to fix your phone charger. The process is not challenging if you find the cord’s sore point. Let us see the sequence of actions you should follow.

Pay Attention to the Cable and Port's Integrity

A slightly bend-in thin cord inside the USB cable usually results in unstable or no contact. Besides, the entire cord might be fractured and have other damages. In addition, the cable itself or areas close to the plug system are vulnerable to corruption, whether the cable comes with a removable USB. So, why isn't my charger working? It is time to overview all trouble spots:

1. The cable has suffered from a significant strain at the power line breakpoint.

If you have the same or similar problem, the way out is quick and easy.

• Peel the outer layer using a wire cutter or common scissors.
• Take wires’ ruined areas away and adjust the length for a seamless connection.
• Delete nearly a 0.2-centimeter layer of insulating material on the cord is all sides.

It would be better to be on the safe side and use tape to enhance insulation and secure the cord. When everything is done, try to connect the wires using a crimper. Is it okay? You have coped with a broken charger!

2. The connection plug area got hit.

In most cases, you have to bid farewell to your charging set if it is damaged close to the connector. However, it is worth trying. To that end, you should buy a compatible connector. Then, follow the following steps:

• Cut the cord at the fraction point.
• Remove nearly 0,5 cm of the protective sheath over the conductor and 0.2 cm of insulation.
• Match the wires based on the micro USB and USB diagram.

Seal the plug and use insulation tape for more security.

3. Corruption near a power unit is noted.

“How to fix my phone charger if I cannot attach the USB?” Let us make things straight right now:

• Chop off the wire in a damaged spot near the power supply.
• In addition, remove the part of a feeder.
• Take away outdated wires.
• Insulate new wires and solder them to the charging unit’s motherboard.

Then, join the parts of the charger cover.

4. External damage with still workable cable.

In this case, people tend to neglect the issue — a big mistake. Hence, take the time to join the cord’s ripped parts with the insulation tape to save the cable’s working condition.

What if the Charger Adapter is Damaged

“Why does my charger not work?” Maybe, you should focus on the adapter. For this purpose, find the voltage rating and amperage. Then, check the adapter to see whether it provides voltage via a multimeter set up in DC voltage mode by plugging your adapter into a power jack.

Do you see the proper voltage? The wrong number of volts indicates a broken part. Then, if your adapter is okay, but it loosens and wiggles after connecting to a mobile phone or a tablet, the problem might be in a charging port or a device.

So, how to make my charger work if the adapter is broken? Just fix it! If the front connector is a meltdown, you should replace the old jack with a new one:

• Cut off the old jack and remove the wires’ plastic cover and insulation.
• Use the voltmeter to power the cord and check the voltage to clarify positive and negative wires.
• Put on the plastic part of a new jack’s cover.
• Put a couple of shrink tubes for wires’ insulation inside the cord and the wires inside them.
• Wrap a new jack’s metal surface with sandpaper.
• Solder two wires to a new jack on its sides.
• Put some insulation between positive and negative wires.

Test your new jack to ensure the adapter’s proper work.

Remove Dirt from Your Phone’s Charging Port

“Why isn’t my charger working after revealing its good condition when connecting it to other devices?” A dirty charging port is the most obvious reason for the cable not going in fully, preventing a good connection. How to handle a build-up of lint or dust?

91-percent alcohol is a win-win solution since it is non-conductive and safe to go ahead and squirt a bit of liquid to loosen up and dissolve all sorts of dirt. So, how to make a charger work again in this situation? First, turn the device off, take the fluid, and put it on something small and thin like a tweezer. Then, stick it in and carefully remove any debris from the port.

Re-start Your Mobile Phone

“Why does my charger not work after multiple tests and checks?” If everything seems okay with the cable, glitches in your device may cause problems with its powering. Hence, it is rational to switch off your smartphone or tablet and make it on again. Then, try to connect the device to your charging unit again. The problem is solved once the power enters your phone. At the same time, the reboot helps retain memory and avoid crashes. It also makes the phone run smoothly and adds life to its battery.

How to Fix Your Cable with Sugru

How to fix a broken charger to make it serve as long as possible? Surgu is the modern material for a reliable sticking to many materials like plastic, metal, ceramics, and others. Initially soft and malleable, Sugry becomes a heavy-duty silicone rubber in 12-24 hours. Moldable glue is the most advanced tool to fix things when the charger is broken.

Sugru makes safe bonds without damaging surfaces, resistant to water and temperatures from 0 to 350 degrees Fahrenheit. And no mess around! Although this glue is the material for many applications, it is perfect for strengthening power cords and fixing electronics.

Is it easy to use? It is so simple that it can be comparable with Play-Doh. Let us see how to make a charger work again using Sugru.

Step 1: Open your Sugru

It would be best to prepare the cord first to make your charger work, meaning cleaning up the surface to ensure the adhesive compound will hold onto it. To that end, one can use a rag dipped in rubbing alcohol. Once the cable is free of debris, dry it by ridding off any alcohol residue.

Opening your Sugru is the next step. Unpack the sticker, take the glue, and thoroughly knead it up for about half a minute until it feels consistent.

Step 2: Stick It to the Surface

When your Surgu is mixed up well, roll it into a long sausage and flatten it a little to cover the necessary area on your cable. Thus, the material is ready to adhere and help you get your charger to work. So, stick the prep circuit to your cleaned cord. While proceeding, bear in mind molding the glue as quickly as possible before it starts drying up.

Step 3: Give It the Desired Shape

Do you want to get a charger to work and brag about the quality job? First, make sure you have tightly wrapped Surgu around the cable’s surface. Then, when you are done shaping it, try to rub it to make the glue’s surface even and smooth.

Step 4: See How it Becomes the Rubber

Since the material takes up to 24 hours to turn into silicone, leave your upgraded cable untouched to let it dry completely. As soon as Surgu dries, you get a sturdy and reinforced cord to feed your mobile device hassle-free. Now, you can call your friend, brag about your success, and advise how to fix a broken charger.